This section explains general cautions that must be followed in order to use this printer safely.

$graphics\warning.gif$

$graphics\NZILG010.gif$

Do not install this printer in the following places.
It may cause an injury if the printer falls down.

•	On a shaky stand
•	Slanting location
•	Places where vibration of other machines etc. is transmitted

$graphics\NZILG010.gif$

Do not stamp on this printer or place heavy things on top of it.
It may cause an injury if the printer falls down.

$graphics\NZILG010.gif$

Do not block the vent by covering the printer with cloths, such as a blanket or tablecloth.
If the vent is blocked, heat may accumulate inside the printer and it may cause fire.

$graphics\NZILG010.gif$

Do not install the printer where it is humid or dusty.
It could lead to an electric shock and fire.

$graphics\NZILG010.gif$

Do not use a damaged power cable.
It could lead to an electric shock and fire.

$graphics\NZILG010.gif$

Do not take out or insert the power plug with a wet hand.
This could lead to an electric shock.

$graphics\NZILG010.gif$

Do not connect an earth wire to the following places.

•	Gas pipe There is a possibility of ignition and explosion.
•	Earth wire of telephone cables and lightning rods Heavy current might flow whenever lightning strikes.
•	Water pipe and faucet The earth might not work if a plastic pipe is connected in the middle of the metal pipe.

$graphics\NZILG010.gif$

Do not insert or drop metal or flammable objects into the printer through openings such as a vent.
It could lead to an electric shock or fire.

$graphics\NZILG010.gif$

If foreign substances or liquids such as water entered the printer, do not use the printer as it is.
It could lead to an electric shock or fire.
Immediately turn OFF the power switch, disconnect the power plug from the electric socket, and contact your local MUTOH dealer.

$graphics\NZILG009.gif$

Wire the various cords as directed in the Operation Manual.
Mistaken wiring could cause fire.

$graphics\NZILG009.gif$

Be sure to use the power cable supplied with the printer.
Using other power cables can cause an electric shock or fire.

$graphics\NZILG009.gif$

Make sure to use only the specified power supply (AC 100 V to 120 V or AC 220 V to 240 V).
If a power supply other than the specified voltage is used, it could cause an electric shock and fire.

$graphics\NZILG009.gif$

Take power for the printer directly from the power socket (AC 100 V to 120 V or AC 220 V to 240 V).
Do not use multiple plugs on the same socket.
This could generate heat and might cause fire.

$graphics\NZILG009.gif$

Be sure to use a dedicated power socket with earth wire for the power supply, and connect it to the earth wire.
If the earth wire is not connected, an electric shock or fire may occur.

$graphics\caution.gif$

$graphics\NZILG010.gif$

Pay attention to the following points when handling power cable.

•	Do not do anything forcefully on the power cable.
•	Do not put heavy objects on the power cable.
•	Do not bend, twist or pull the power cable by force.
•	Do not route the power cable near heating appliances.

$graphics\NZILG010.gif$

Pay attention to the following points when handling the power supply plug.
Any mishandling of the power cable could cause a fire.

•	Make sure that no foreign substances such as dust etc. are stuck to the power plug.
•	Make sure that the power plug is firmly inserted to the edge of the power socket.

$graphics\NZILG010.gif$

When handling ink cartridges, pay attention so that ink does not get into your eyes or stick to your skin.
If ink gets into your eyes or sticks to your skin, immediately wash it off with water.
Failing to do so might cause irritation or light inflammation of eyes.
In case of any abnormality, consult a physician immediately.

$graphics\NZILG010.gif$

Do not disassemble ink cartridges.
If disassembled, there is a possibility that ink might come into contact with eyes or skin.

$graphics\NZILG010.gif$

Do not operate the media loading lever during initial operation and printing of the product.
The print head portion may touch the pressurizing roller portion, and cause a malfunction.

$graphics\NZILG010.gif$

Do not use volatile solvents such as thinner, benzene, or alcohol.
These solvents could cause damage to the paint.

$graphics\NZILG010.gif$

Be careful that no moisture enters the printer.
There is a possibility that the electric circuit inside the printer is short circuited.

$graphics\NZILG010.gif$

Do not open covers attached using screws under any circumstances.
This may cause an electric shock or a malfunction.

$graphics\NZILG010.gif$

While cleaning the cleaning wiper

•	Do not touch the cleaning wiper and head cap unit. Head cleaning may not be performed correctly because of oil from your hands.
•	Make sure to wipe the print head with a dry poly-knit wiper. A wet poly-knit wiper may cause the print head to clog.

$graphics\NZILG010.gif$

Do not slant the printer, prop it against a wall or turn it upside down.
There is a possibility that ink inside the printer may leak.
Moreover, normal operation after shifting (to these positions) cannot be guaranteed.

$graphics\NZILG009.gif$

When unpacking and moving the printer to an installation point, be sure to have the following number of personnel.

•	VJ-1304W: three or more

$graphics\NZILG009.gif$

When installing the stand to the printer, make sure to have the following number of personnel.

•	VJ-1304W: three or more

$graphics\NZILG009.gif$

While installing the stand, be sure to turn OFF the power and pull out the power plug.
It could lead to an electric shock.

$graphics\NZILG009.gif$

When you do not use the printer for a long period, make sure to pull out the power plug from the power socket for safety.

$graphics\NZILG009.gif$

Make sure to connect an earth wire to the earth connection that meets the following standards.

•	Earth terminal of power socket
•	Earth wire with copper plate which is buried at 650 mm or more, deep in the ground.

$graphics\NZILG009.gif$

Load roll media on an even surface such as a desk.
If you load roll media with the scroller standing vertical, there is a possibility that the scroller might get damaged.

$graphics\NZILG009.gif$

Pay attention to the following points when you cut roll media.
Mishandling the razor blade may cause a cut on your finger or hand.

•	When you hold media, do not place your finger on the media cut groove.
•	Move the razor blade along the media cut groove.

$graphics\NZILG009.gif$

When cleaning the printer except the cleaning wiper, be sure to turn OFF the power and disconnect the power plug.

$graphics\NZILG009.gif$

Move the printer maintaining a horizontal position.