Various settings of the printer are configured.

Setup item

Description

MediaType

Sets up the media type to print.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.1 MediaType menu

Effect

Sets up the Effect menu.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.2 Effect menu

Flushing

Set up the Flushing operation while printing.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.3 Flushing menu

Side Margin

Specifies the right and left margins of printed media.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.4 Side Margin menu

Media Initial

Decides whether to detect the width and front edge of the media when initializing the media.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.5 Media Initial menu

Media Width/MediaWidth

Specifies the media width between the loading mark and the left end if media detection is not performed during media initialization.

Displays the detected media width if media detection is performed during media initialization.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.6 Media Width/MediaWidth menu

Origin

Sets the beginning of printing (origin) of the print data.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.7 Origin menu

Prev. Stick

Sets up to prevent media from sticking when printing starts.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.8 Prev. Stick menu

HeadFan

Sets up head fan operation.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.9 HeadFan menu

CR Movement

Sets up the range that the print head moves while printing.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.10 CR Movement menu

OverwriteCnt

Sets up the overwrite count per line.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.11 Overwrite Cnt menu

Overwrite Wait

Sets up the waiting time while overwrite printing.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.12 Overwrite Wait menu

Slant Check

Sets up slanting detection during media loading.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.13 Slant Check menu

Auto Cleaning

Sets up the time for auto cleaning during printing.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.14 Auto Cleaning menu

Ink Status

Displays information (ink status) of ink cartridge installed in the ink cartridge slot.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.15 Ink Status menu

Roll Length

Sets up the roll media length.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.16 Roll Length menu

Head Wash

Performs Head washing.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.17 Head Wash menu

CR Maint.

Performs maintenance.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.18 CR Maintenance menu

Initialization

Returns the settings of the printer to default.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.19 Initialization menu

Life Times

Displays the operational life time of each part.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.20 Life Times menu

IP Address

Sets the IP address of the printer.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.21 IP Address menu

Subnet Mask

Sets the subnet mask of the printer.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.22 Subnet Mask menu

Gateway

Sets the gateway.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.23 Gateway menu

Temporary

Displays the settings of "Off" or "ALL Off" in the Selection menu in the Setup menu temporarily.

•	[Enter] key: returns to the previous menu with all set up items displayed.
•	[Cancel] key: returns to the previous status in the Selection menu when the Setup menu is displayed. $graphics\nzilg007.gif$ 5.5 Selection menu

—

•	[Cancel] key: shifts to the previous menu. $graphics\nzilg007.gif$ 5 Panel setup menu

5.1.1 MediaType menu

Sets up the media type to print.

Setup item

Setting

Description

Media

Type 1

Sets up the media type to print.
It is possible to set 30 different user settings as "Type 1-30" for printing.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.1.1 User media menu

Type 2

…

Type 29

Type 30

—

•	[Cancel] key: saves the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1 Setup menu

5.1.1.1 User media menu

Various settings on the user media are configured.
In the User media menu, 30 different settings can be set as Type 1 to 30 for the following printing operation.

•

If media other than recommended one (user media) is used, the following problems may occur.

•	Media detection error
•	Slant, snag and wrinkle of media
•	Media jams
•	Favorable print quality cannot be obtained due to blots, blurs or dirt of ink.
•	End detection of roll media cannot be performed, etc.

The problems caused by the use of user media will not be covered by the warranty and repair expenses will be paid by the customer.
For details, contact your local MUTOH dealer.

Setup item

Setting

Description

Type 1 to 30

Print Mode

Sets up the print mode according to the usage of print data or print speed.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.1.1.1 Print Mode menu

PF Adjust

Various settings on the Media feed compensation are configured.

•	[>] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.1.1.2 Dist.Adj menu

Pre Heater

Sets up the Pre Heater temperature.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.1.1.3 Pre Heater menu

Platen Heater

Sets up the Platen Heater temperature.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.1.1.4 Platen Heater menu

After Heater

Sets up the After Heater temperature.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.1.1.5 After Heater menu

StandbyHeating

Sets up whether to preheat the heater while the printer is in standby mode.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.1.1.6 StandbyHeating menu

Vacuum Fan

Sets up vacuum fan operation.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.1.1.7 Vacuum Fan menu

—

•	[Cancel] key: shifts to the previous menu. $graphics\nzilg007.gif$ 5.1.1 MediaType menu

5.1.1.1.1 Print Mode menu

Settings for print quality (print mode) are set according to the usage of print data or print speed.

Setup item

Setting

Description

Mode

Quality 1

Sets up print mode.

•	Quality 1 to 4: Sets up to perform high quality printing.

•	Graphics 1 to 2: Sets up to perform standard printing.
•	Banner 1 to 4: Sets up to perform high speed printing.

Displays details of each print mode while pressing [>] key.
$graphics\nzilg007.gif$ Details of print mode

•	When "Banner 1" or "Banner 2" is set in the Print Mode menu, "PalettePrint" is not displayed in the Test Print menu. $graphics\nzilg007.gif$ 5.2 TestPrint Menu

Quality 2

Quality 3

Quality 4

Graphics 2

Banner 1

Banner 2

Banner 3

Banner 4

—

•	[Enter] key: saves the setting and shifts to the previous menu.
•	[Cancel] key: cancels the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1.1.1 User media menu

Details of print mode

The settings for print quality registered in each print mode are as follows.

Print Mode

Resolution

Print speed

Pass

Direction

Quality 1

1440×1440 dpi

Q (high quality)

16 times

Uni (unilateral)

Quality 2

1440×720 dpi

Q (high quality)

8 times

Uni (unilateral)

Quality 3

720×720 dpi

Q (high quality)

8 times

Uni (unilateral)

Quality 4

720×720 dpi

Q (high quality)

8 times

Bi (bidirectional)

Graphics 1

720×720 dpi

N (normal)

8 times

Uni (unilateral)

Graphics 2

720×720 dpi

N (normal)

8 times

Bi (bidirectional)

Banner 1

540×720 dpi

N (normal)

6 times

Uni (unilateral)

Banner 2

540×720 dpi

N (normal)

8 times

Bi (bidirectional)

Banner 3

720×720 dpi

Q (high quality)

4 times

Uni (unilateral)

Banner 4

720×720 dpi

N (normal)

4 times

Bi (bidirectional)

5.1.1.1.2 Dist.Adj menu

Various settings on the Media feed compensation are configured.

Setup item

Setting

Description

Initial Print

Performs initial adjust print.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ (1) Initial Print menu

Initial Change

Set up Initial Adjust Change.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ (2) Initial Change menu

Confirm Print

Perform Confirm Print.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ (3) Confirm Print menu

Micro Print

Perform Micro Adjustment Print.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ (4) Micro Print menu

Micro Change

Set up Micro Adjustment Change.

•	[Enter] key: shifts to the sub menu. $graphics\nzilg007.gif$ (5) Micro Change menu

—

•	[Cancel] key: shifts to the previous menu. $graphics\nzilg007.gif$ 5.1.1.1 User media menu

(1) Initial Print menu

Perform initial adjust print.

Setup item

Setting

Description

Feed Length

100mm to <250mm> to 500mm

Changes the length (feed length) of the media feed direction for initial adjust print.

•	[Enter] key: Determines the setting. "Printing" is displayed on the operation panel and initial adjust print starts. After printing, the printer enters Normal.

—

•	[Cancel] key: cancels the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1.1.1.2 Dist.Adj menu

(2) Initial Change menu

Set up Initial Adjust Change.

Setup item

Setting

Description

Init.

200.0mm to <250.0mm> to 300.0mm

Set up Initial Adjust Change.

—

•	[Enter] key: saves the setting and shifts to the previous menu.
•	[Cancel] key: cancels the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1.1.1.2 Dist.Adj menu

(3) Confirm Print menu

Perform Confirm Print.

Setup item

Setting

Description

Feed Length

100mm to <250mm> to 500mm

Changes the length (feed length) of the media feed direction for Confirm Print.

•	[Enter] key: Determines the setting. "Printing" is displayed on the operation panel and initial adjust print starts. After printing, the printer enters Normal.

—

•	[Cancel] key: cancels the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1.1.1.2 Dist.Adj menu

(4) Micro Print menu

Perform Micro Adjustment Print.

Setup item

Setting

Description

Micro Print

Printing

Prints the following PF pattern (micro adjustment) with a focus on the micro adjustment value.

•	Printing interval: ±1 pulse

—

•	[Cancel] key: shifts to the previous menu. Stops printing and returns to the previous menu if printing is in progress. $graphics\nzilg007.gif$ 5.1 Setup menu

(5) Micro Change menu

Set up Micro Adjustment Change.

Setup item

Setting

Description

Micro Change

–20 pulse to <0 pulse> to 20 pulse

Set up Micro Adjustment Change.

—

•	[Enter] key: saves the setting and shifts to the previous menu.
•	[Cancel] key: cancels the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1 Setup menu

5.1.1.1.3 Pre Heater menu

Sets up the Pre Heater temperature.
Set up to preheat the media before printing and insulate the temperature change in the printer section.

•	Preset temperature of Pre Heater varies depending on the media. For preset temperature of Pre Heater, refer to the "Recommended media list".

Setup item

Setting

Description

Pre Heater

Off / <30° C> to 50° C

Sets up the Pre Heater temperature.

$graphics\VJ1204A802A.gif$

1.	Roll media
2.	Pre Heater
3.	Print head

—

•	[Enter] key: saves the setting and shifts to the previous menu.
•	[Cancel] key: cancels the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1.1.1 User media menu

5.1.1.1.4 Platen Heater menu

Sets up the Platen Heater temperature.
Set up this menu to warm up ink and improve print quality.

•	Preset temperature of Platen Heater varies depending on the media. For preset temperature of Platen Heater, refer to the "Recommended media list".

Setup item

Setting

Description

Platen Heater

Off / <30° C> to 50° C

Sets up the Platen Heater temperature.

$graphics\VJ1204A803A.gif$

1.	Roll media
2.	Platen Heater
3.	Print head

—

•	[Enter] key: saves the setting and shifts to the previous menu.
•	[Cancel] key: cancels the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1.1.1 User media menu

5.1.1.1.5 After Heater menu

Sets up the After Heater temperature.
Set this menu to dry printing.

•	Preset temperature of After Heater varies depending on the media. For preset temperature of After Heater, refer to the "Recommended media list".

Setup item

Setting

Description

After Heater

Off / <30° C> to 50° C

Sets up the After Heater temperature.

$graphics\VJ1204A804A.gif$

1.	Roll media
2.	After Heater
3.	Print head

—

•	[Enter] key: saves the setting and shifts to the previous menu.
•	[Cancel] key: cancels the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1.1.1 User media menu

5.1.1.1.6 StandbyHeating menu

Sets up whether to preheat (idle heat) each heater when the printer is in standby mode.

Setup item

Setting

Description

StandbyHeating

Off

Idle heat is not performed.

<On>

Idle heat is performed.

—

•	[Enter] key: saves the setting and shifts to the previous menu.
•	[Cancel] key: cancels the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1.1.1 User media menu

5.1.1.1.7 Vacuum Fan menu

Sets up vacuum fan operation.

Setup item

Setting

Description

Vacuum Fan

Low

Set when there is a possibility of a paper jam caused by failure in media loading when using soft media.

<High>

Set when using general media.

—

•	[Enter] key: saves the setting and shifts to the previous menu.
•	[Cancel] key: cancels the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1.1.1 User media menu

5.1.2 Effect menu

Sets up the Effect menu.
Set up this menu when you want to improve print quality by adjusting the set print mode.

•	The print quality may not be improved depending on the printing condition.

Setup item

Setting

Description

Effect

None 1

The Effect function is not used.
If obvious white lines or uneven print density appear on printed media in "None 1", set to "None 2".

None 2

The printing joint will be the wave form.
It will be improved the print quality.
If obvious white lines or uneven print density appear on printed media in "Wave 1", change the setting to the one with the best print result in "Wave 2 to 4".

Wave 2

Wave 3

Wave 4

Fine&Wave 1

Perform printing at a slow speed compared with "Wave".
Set up this menu when improving the print quality compared with "Wave".
If obvious white lines or uneven print density appear on printed media in "Fine&Wave 1", change the setting to the one with the best print result in "Fine&Wave 2 to 4".

Fine&Wave 2

Fine&Wave 3

Fine&Wave 4

A-S.Fine&Wave

Performs "Wave" printing using one side of the nozzles of the print head.
Since only one side of the nozzles is used, printing speed becomes half of "Wave 1 to 4"
Set up this menu when improving the print quality compared with "Fine&Wave 1 to 4".

B-S.Fine&Wave

Performs "Wave" printing using the other side of the nozzles of the print head that is used for "A-S.Fine&Wave".
Since only one side of the nozzles is used, printing speed becomes half of "Wave 1 to 4"
Set up this menu when improving the print quality compared with "Fine&Wave 1 to 4".

—

•	[Enter] key: saves the setting and shifts to the previous menu.
•	[Cancel] key: cancels the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1 Setup menu

5.1.3 Flushing menu

Set up the Flushing operation while printing.

Setup item

Setting

Description

Flushing

Origin

Perform the flushing operation to return to the original flushing box every time the print head goes and returns.

•	[Enter] key: saves the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1 Setup menu

Perform the flushing operation on the page margins.
Improve the print quality since returning to the original flushing box.

•	[Enter] key: saves the setting and shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.3.1 Flushing return count menu

—

•	[Cancel] key: cancels the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1 Setup menu

5.1.3.1 Flushing return count menu

Set the frequency (flushing return count) that the print head returns to the original flushing box when setting "On Media" in the Flushing menu.

•	When increasing the flushing return count, clogging may occur while printing continuously.

Setup item

Setting

Description

ReturnCount

Once to <5 times> to 999 times

Set the flushing return count.
Example

•	Once: return to the flushing box on the original side every time the print head goes and returns.
•	5 times: return to the flushing box on the original side every time the print head goes and returns five times.

—

•	[Enter] key: saves the setting and shifts to the previous menu.
•	[Cancel] key: cancels the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1 Setup menu

5.1.4 Side Margin menu

Set up the right and left margins (side margins) while printing.

•	When setting "On Media" in the Flushing menu, the value of the Side Margin menu is disabled and the margin to perform the flushing operation is set automatically. $graphics\nzilg007.gif$ 5.1.3 Flushing menu
•	When using the media holder plate, set the side margin to 10 mm. $graphics\nzilg007.gif$ 4.2.7 Installing media holder plates

Setup item

Setting

Description

Side Margin

<5mm> to 25mm

Set the side margins.

—

•	[Enter] key: saves the setting and shifts to the previous menu.
•	[Cancel] key: cancels the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1 Setup menu

5.1.5 Media Initial menu

Decides whether to detect the width and front edge of the media when initializing the media.

Setup item

Setting

Description

Init.

Off

The media is not detected.

•	Set the media width that is set in the Media Width menu when setting "Off" in the Media detection menu, $graphics\nzilg007.gif$ 5.1.6 Media Width/MediaWidth menu

Top&Width

Detect the media width and edge while initializing the media.

<Width>

Detect the media width while initializing the media.

—

•	[Enter] key: saves the setting and shifts to the previous menu.
•	[Cancel] key: cancels the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1 Setup menu

5.1.6 Media Width/MediaWidth menu

Set up the distance between the right end from 5 mm and the left end if media detection is not performed when initializing the media.
$graphics\nzilg007.gif$ (1) Media Width menu

Displays the detected media width if media detection is performed during media initialization.
$graphics\nzilg007.gif$ (2) MediaWidth menu

$graphics\VJ1204A800A.gif$

No.

Name

Roll media

Media width

(1) Media Width menu

•	Setting a larger value than the media width set in the Media Width menu may cause ink to leak on the media or printer.

Setup item

Setting

Description

Media Width

<1,000 mm> to 1,625 mm

Set the media width.

—

•	[Enter] key: saves the setting and shifts to the previous menu.
•	[Cancel] key: cancels the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1.1.1 User media menu

(2) MediaWidth menu

Setup item

Setting

Description

MediaWidth

**** mm

Display the media width that is detected while initializing.

—

•	[Cancel] key: shifts to the previous menu. $graphics\nzilg007.gif$ 5.1 Setup menu

5.1.7 Origin menu

Sets the beginning of printing (origin) of the print data.
Set the menu when reprinting on the margin with changing the printing data position to the printed media.

Setup item

Setting

Description

Origin

•	X (print head transferring distance): 00000 mm to 99,999 mm
•	Y (media feeding distance): 00000 mm to 9,999mm

Change the print head position and media feeding distance with the following keys.

•	[>] key: Decrease the print head transferring distance.
•	[<] key: Increase the print head transferring distance.
•	[+] key: Increase the media feeding distance.
•	[–] key: Decrease the media feeding distance.

$graphics\VJ1204A801A.gif$

1.	Starting position
2.	Media feeding direction

•	[Enter] key: "Moving Origin Pos." is displayed on the operation panel and the print head moves to the starting position. The following contents is displayed on the operation panel.

Confirm Position→E

•	[Enter] key or after a certain period of time: Determines the setting. Print head returns to the original position. Save the setting and shift to the previous menu. $graphics\nzilg007.gif$ 5.1 Setup menu

—

•	[Cancel] key: cancels the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1 Setup menu

5.1.8 Prev. Stick menu

Sets up to prevent media from sticking when printing starts.

Setup item

Setting

Description

Prev. Stick

Off

The sticking operation is not performed.

<On>

The sticking operation is performed.
Feed the media back and forth to prevent from sticking.

—

•	[Enter] key: saves the setting and shifts to the previous menu.
•	[Cancel] key: cancels the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1 Setup menu

5.1.9 HeadFan menu

Sets up head fan operation.
If print blurring or dot losses occur, activate the head fan.

Setup item

Setting

Description

HeadFan

<Off>

Not activate the fan.

Activates the fan.

—

•	[Cancel] key: saves the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1 Setup menu

5.1.10 CR Movement menu

Sets up the range that the print head moves while printing.

Setup item

Setting

Description

CR Movement

<Data>

The print head changes the range of the print data width.
Improve the print speed since decreasing the transferring range of the print head.

Machine

The print head moves from origin to the maximum paper width.

—

•	[Enter] key: saves the setting and shifts to the previous menu.
•	[Cancel] key: cancels the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1 Setup menu

5.1.11 Overwrite Cnt menu

Sets up the overwrite count per line.

Setup item

Setting

Description

OverwriteCnt

<once> to 9 times

Set the overwrite count.

—

•	[Enter] key: saves the setting and shifts to the previous menu.
•	[Cancel] key: cancels the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1 Setup menu

5.1.12 Overwrite Wait menu

Sets up the waiting time while overwrite printing.

•	Narrow media may not be warmed enough by the heater causing less print quality. In this case, set the Overwrite Wait time and warm up the media.

Setup item

Setting

Description

Overwrite Wait

<0.0 sec.> to sec.0.1 sec. to 5.0 sec.

Set the Overwrite Wait time.

—

•	[Enter] key: saves the setting and shifts to the previous menu.
•	[Cancel] key: cancels the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1 Setup menu

5.1.13 Slant Check menu

Sets up slanting detection during media loading.

Setup item

Setting

Description

Slant Check

Off

Slant Check is not performed.

<On>

Slant Check is performed.

—

•	[Enter] key: saves the setting and shifts to the previous menu.
•	[Cancel] key: cancels the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1 Setup menu

5.1.14 Auto Cleaning menu

Set the auto cleaning interval of this printer.
Since perform the cleaning operation when turning ON the power, prevent from clogging the print head.

Setup item

Setting

Description

Auto Cleaning

Off

The auto cleaning is not performed.

1 hours

The selected time is passed, the auto cleaning is performed.

2 hours

3 hours

4 hours

5 hours

<6 hours>

9 hours

12 hours

18 hours

24 hours

—

•	[Enter] key: saves the setting and shifts to the previous menu.
•	[Cancel] key: cancels the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1 Setup menu

5.1.15 Ink Status menu

Displays information (ink status) of ink cartridge installed in the ink cartridge slot.

•	When displaying the Ink Status menu, use the genuine ink cartridge. If you use an ink cartridge other than the genuine one, ink status is not displayed correctly.

Setup item

Setting

Description

KCMY

0 to 100 (Unit: %)

Residual ink quantity of K, C, M and Y color is displayed.

—

•	[Cancel] key: shifts to the previous menu. $graphics\nzilg007.gif$ 5.1 Setup menu

5.1.16 Roll Length menu

Sets up the roll media length.

Setup item

Setting

Description

Roll media

<Off>

Roll Length is not used.

•	[Enter] key: saves the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1 Setup menu

Roll1

Sets up the roll media length.
The Roll Length setting is set for three types as "Roll1" to "Roll3".

•	[Enter] key: saves the setting and shifts to the sub menu. $graphics\nzilg007.gif$ 5.1.16.1 Roll media length menu

Roll2

Roll3

—

•	[Cancel] key: cancels the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1 Setup menu

5.1.16.1 Roll media length menu

Sets up the roll media length.

Setup item

Setting

Description

Length

1 m to <30 m> to 99 m

Set the roll media length.

•	When replacing the roll media, adjust the roll media length again. If the roll media length is not set, the residual quantity of roll media is not displayed correctly.

—

•	[Enter] key: saves the setting and shifts to the previous menu.
•	[Cancel] key: cancels the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1 Setup menu

5.1.17 Head Wash menu

Performs Head washing.

•	Make sure to use a dedicated cleaning fluid (model No.: VJ-MSINK3-CL220).

Setup item

Setting

Description

Head Wash

Start

Performs Head washing.

•	[Enter] key: Perform the Head washing operation. The following contents is displayed on the operation panel.

Remove Cartridges

Remove the ink cartridge, and install the cleaning cartridge.

$graphics\nzilg007.gif$ 6.1.1 Replacing ink cartridges

—

•	[Cancel] key: shifts to the previous menu without Head washing. $graphics\nzilg007.gif$ 5.1 Setup menu

5.1.18 CR Maintenance menu

Performs maintenance.
Use this to clean the cleaning wiper and the outside of the print head.
$graphics\nzilg007.gif$ 6.2.4 Cleaning the cleaning wiper
$graphics\nzilg007.gif$ 6.2.5 Cleaning around the print head

Setup item

Setting

Description

CR Maint.

Start

Performs maintenance.

•	[Enter] key: The print head moves to the left. The cleaning wiper moves forward.

End

Completes maintenance.

•	[Enter] key: The print head returns to its original position. The cleaning wiper returns to its original position.

—

•	[Cancel] key: shifts to the previous menu without maintenance. $graphics\nzilg007.gif$ 5.1 Setup menu

5.1.19 Initialization menu

Returns the settings of the printer to default.

Setup item

Setting

Description

Initialization

ALL

All settings can be returned to factory default.

MediaType

The settings of the MediaType menu is returned to factory default.

Except MediaType

The settings value other than the MediaType menu is returned to factory default.

—

•	[Enter] key: "Initialing" is displayed on the operation panel and the printer initializes the setting.

•	[Cancel] key: shifts to the previous menu without initialization. $graphics\nzilg007.gif$ 5.1 Setup menu

5.1.20 Life Times menu

Displays the operational life time of each part.

Setup item

Setting

Description

Life Times

Head

Display the operational life of each part.

•	The operational life of a part is indicated by five asterisks (100 %).
•	As the part deteriorates, the number of asterisks decreases one by one (20 %).
•	The part should be changed when all of the asterisks have disappeared, and "Change" is displayed. Contact your local MUTOH dealer to ask for replacing parts.

Pump

CR Motor

PF Motor

—

•	[Cancel] key: shifts to the previous menu. $graphics\nzilg007.gif$ 5.1 Setup menu

•

When replacing a part that its operational life has ended,

•	No charge for replacing within the warranty period or under the contract.

•	You are liable for the cost of repairs under conditions other than mentioned above.

•

Do not keep using the part which has reached its life span.Problems caused by doing so will not be covered by the warranty.

5.1.21 IP Address menu

Sets the IP address of the printer.

•	Be sure to set the IP address after consulting the network administrator.

Setup item

Setting

Description

IP Address

000.000.000.000 to
<192.168.001.253> to
255.255.255.255

Change the IP address to operate the following keys.

•	[+] key: increases the setting value.
•	[–] key: decreases the setting value.
•	[Enter] key: changes the setting for the next segment.

—

•	[Cancel] key: saves the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1 Setup menu

5.1.22 Subnet Mask menu

Sets the subnet mask of the printer.

•	Be sure to set the subnet mask after consulting the network administrator.

Setup item

Setting

Description

Subnet Mask

000.000.000.000 to
<255.255.255.000> to
255.255.255.255

Change the subnet mask to operate the following keys.

•	[+] key: increases the setting value.
•	[–] key: decreases the setting value.
•	[Enter] key: changes the setting for the next segment.

—

•	[Cancel] key: saves the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1 Setup menu

5.1.23 Gateway menu

Sets the gateway.

•	Be sure to set the gateway after consulting the network administrator.

Setup item

Setting

Description

Gateway

000.000.000.000 to
<192.168.001.254> to
255.255.255.255

Change the gateway to operate the following keys.

•	[+] key: increases the setting value.
•	[–] key: decreases the setting value.
•	[Enter] key: changes the setting for the next segment.

—

•	[Cancel] key: saves the setting and shifts to the previous menu. $graphics\nzilg007.gif$ 5.1 Setup menu